Usmile Matek Systems F405-STD BetaFlight STM32F405RGT6 Flight Controller Built-in OSD Inverter for SBUS Input for Martian Alien Carbon Fiber quadcopter X frame Carbon Fiber FPV Racing Quad Drone Frame Review

Usmile Matek Systems F405-STD BetaFlight STM32F405RGT6 Flight Controller Built-in OSD Inverter for SBUS Input for Martian Alien Carbon Fiber quadcopter X frame Carbon Fiber FPV Racing Quad Drone Frame

    This fits your .
  • Enter your model number to make sure this fits.
  • Nice layout. Makes for a very nice clean build especially together with the FCHUB-6S Hub PDB http://www.amazon.com/dp/B073Z7KPVZ.
  • Supports a non inverted SBUS signal input with 5x UARTs, All pins are well labeled and easy to solder. ESC signal pins in corners.
  • With ribbon cable between the FC and PDB, it makes for a clean install.
  • OSD feature is also a great feature as well you can now change pids in the field without a laptop
  • For more detailed info about connection guide/Boot mode/OSD/Firmware downloads, please visit http://www.mateksys.com/?portfolio=f405-std

This FC is a great combo with Matek FCHUB-6S hub, makes for a clean build, check it here http://www.amazon.com/dp/B073Z7KPVZ
MCU: 168MHz STM32F405RGT6
IMU: 32K ICM20602 gyro/accelerometer (SPI)
Baro: BMP280 (I2C)
OSD: BetaFlight OSD w/ AT7456E chip
Blackbox: MicroSD card slot (SD/SDHC)
VCP, UART1, UART2, UART3, UART4, UART5
Built in inverter for SBUS input (UART2-RX)
PPM/UART Shared: UART2-RX
SoftSerial on TX2, S5 or S6 optional
Camera control on S6 or DAC optional
Smartaudio & Tramp VTX protocol supported
Battery Voltage Sensor: 1:10
Current Sensor: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)
BEC 5V: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)
LDO 3.3V: Max.300mA
I2C1 SDA & SCL: Yes
WS2812 Led Strip : Yes
Beeper : Yes
RSSI: Yes
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
6x PWM / DShot outputs without conflict
2x 2812LED outputs option
5x UARTs
1x Group of 5V/G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
1x pair I2C1 pads
1x Side-press button for BOOT(DFU) mode
1x 16pin bottom mounted FFC Slot for FCHUB-6S, FCHUB-VTX or FCHUB-W connection
36x36mm PCB with 30.5mm mounting holes
w/ 2x 0.5mm*16Pin 5cm Flexible Flat Cable
w/ 4pcs M3 Anti-vibration Standoffs

Other parts you might be interested:
5.8G fpv receiver for Android phone http://www.amazon.com/dp/B06ZZG6GSR
5.8G FPV receiver for iphone/ipad/Android www.amazon.com/dp/B0741T9DT8
Self-binding Micro DSM2 DSMX receiver http://www.amazon.com/dp/B01NAEN5RG http://www.amazon.com/dp/B01JWFCRYA
5 Inch 800*480 400lux LED Monitor http://www.amazon.com/dp/B01K1U7LU0
1.5W Super Bright LED Head Lights http://www.amazon.com/dp/B019FD678G

Leave a Reply

Your email address will not be published. Required fields are marked *